US Robotics 56 K SOFTMODEM - COMMAND REFERENCE REV 1 User Manual Page 15
- Page / 108
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
56K Softmodem
Command Reference
- 9
sequence. The dial string (<dial string>, including modifiers and the telephone
number) is entered after the D command.
A dial string can be up to sixty characters long. Any digit or symbol may be dialed
as touchtone digits. Characters such as spaces, hyphens, and parentheses are
ignored by the modem and may be included in the dial string to enhance
readability.
Table 3-3:
Dial Modifiers
E<value>—Echo Command
Use this command to enable or disable the 56K Softmodem echo feature. When
the echo feature is selected and the modem is in command mode, characters sent
to the modem are sent back to the host and displayed on the monitor.
Result codes:
OK if <value> = 0—1.
ERROR if <value> does not equal 0—1.
Modifier Function Name Description
L Dial the last number Instructs the modem to dial the last number dialed. This modi-
fier is valid only if it is the first symbol of the dial string. All con-
secutive characters are discarded.
P Select pulse dialing
—
T Select tone dialing (default)
—
W Wait for dial tone Instructs the modem to wait for a second dial tone before
processing the dial string.
, Dial pause Instructs the modem to pause before processing the next char-
acter in the dial string. Register S8 (see “S8—Pause Time for
Dial Delay Modifier” on page 88) determines the length of the
pause.
! Hook flash Instructs the modem to go on-hook for 0.5 s and then return to
off-hook.
@ Wait for quiet answer Instructs the modem to wait for 5 s of silence after dialing the
number. If silence is not detected, the modem sends a NO
ANSWER result code back to the user.
; Return to command mode Instructs the modem to return to command mode after it has
finished dialing without disconnecting the call. This modifier
must be the last character in the dial string.
$ Bong tone detection
—
S=<location> Dial from register Instructs the modem to dial a telephone number previously
stored using the &Z<location>=<dial string> command. Valid
storage locations are 0—3.
- 56K Softmodem 1
- Command 1
- Reference 1
- Contents 3
- Introduction 7
- AT Command Conventions 9
- Basic Syntax Commands 10
- Extended Syntax Commands 10
- S Register Conventions 11
- Other Document Conventions 11
- AT Command Set 13
- Dial Modifiers 15
- TI<value> Commands 17
- ATI11 Command Results 19
- N<value> Commands 21
- Q<value> Commands 22
- &M<value> Commands 28
- Result codes: 31
- \A0 64 characters 32
- \A1 128 characters 32
- \A2 192 characters 32
- -C<value> Commands 38
- +A8T=<sig 42
- >—Send V.8 bis 42
- +A8T Extended Syntax Commands 42
- <max_codewords_tx> 45
- Valid <timed> Values 47
- +MR Extended Syntax Commands 61
- Fax Commands 69
- +FRH Commands 73
- +FRM Commands 74
- Test and Debug AT Command 77
- Result Codes 89
- Result Code Numeric 90
- Description 90
- S-Registers 92
- S-Register Definitions 94
- Default: 7 (00000111b) 98
- Command Reference 104
Related products and manuals for Modems US Robotics 56 K SOFTMODEM - COMMAND REFERENCE REV 1
(158 pages)
(30 pages)
(44 pages)
(80 pages)Canon OC210 manuály
Uživatelské manuály a uživatelské příručky pro Videokamery Canon OC210.
Poskytujeme 2 manuály pdf Canon OC210 ke stažení zdarma podle typů dokumentů: Manuál s instrukcemi, Uživatelský manuál
Comments to this Manuals